DG201ABK DATASHEET PDF

Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. In either case, source-to-body diodes can be forward biased and conduct current from the signal source. Lab 6 in this note. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply.

Author:Kigarr Shaktirisar
Country:Central African Republic
Language:English (Spanish)
Genre:Medical
Published (Last):1 February 2013
Pages:399
PDF File Size:13.72 Mb
ePub File Size:2.5 Mb
ISBN:867-9-86336-539-1
Downloads:42294
Price:Free* [*Free Regsitration Required]
Uploader:Kaganos



Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. In either case, source-to-body diodes can be forward biased and conduct current from the signal source.

Lab 6 in this note. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply. Package Information continued The package drawing s in this data dataaheet may not reflect the most current specifications. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet.

Dgab, D1, dgabk E1 dimensions do not include mold flash or protrusions. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or dabk rights of third parties which may result from its use. Asa cum sunt, la Tine vin! Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with the positive and negative supplies as shown in Figure 2.

VO is datasheeh steady state output with switch on. Information furnished by Intersil is believed to be accurate and reliable. SR Datasheet — Micropower Direct. B1 maximum dimensions do not include dambar protrusions. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders.

For this configuration dimension b3 replaces dimension b2. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

E and eA are measured with the leads constrained to be perpendicular to datum -C. Putere n-am, Tu-mi fii sprijin. For more information on TYP values see Note 2. Mold flash or protrusions shall not exceed 0.

Parameter guaranteed by design or characterization. No circuit patent licenses are implied. In the OFF state each channel blocks voltages up to the supply rails. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected. A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown.

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. Limit diode current to maximum current ratings. Dimensions b1 and c1 apply to lead base metal only. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Dambar protrusions shall not exceed 0. All Rights Reserved All other trademarks mentioned are the property of their respective owners. Dimension Q shall be measured from the seating plane to the base plane. Maxim reserves the right to change the circuitry and specifications without notice at any time.

Dimension M applies to lead plating and finish thickness. An enable input is provided. Most Related.

FROM THE VOLTURNO TO THE WINTER LINE PDF

DG201ABK DATASHEET PDF

Malarisar Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. B1 maximum dimensions do not include dambar protrusions. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. N is the maximum number of terminal positions.

BENEFICIESE ESCUELA MINISTERIO PDF

Arashirr This dimension allows for off-center lid, meniscus, and glass overrun. Typical values are for design aid only, not guaranteed and not datasneet to production testing. VO is the steady state output with switch on. For more information on TYP values see Note 2. Limit diode current to maximum current ratings. In case of conflict between English and Metric dimensions, the inch dimensions control. Selected parts for the query dg Dimension Q shall be measured from the seating plane to the base plane.

KEOPE ARKASA PDF

.

HARI TATYA PDF

.

Related Articles