To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Attention-when the product is installed in Rack: 1.
|Published (Last):||28 December 2010|
|PDF File Size:||4.65 Mb|
|ePub File Size:||5.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen.
Attention-when the product is installed in Rack: 1. Prevention against overloading of branch circuit When this product is installed in a rack and is supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit.
Providing protective earth When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection.
Internal air ambient temperature of the rack When this product is installed in a rack, please make sure that the internal air ambient temperature of the rack is within the specified limit of this product. Prevention against achieving hazardous condition due to uneven mechanical loading When this product is installed in a rack, please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading.
Replace only with the same or equivalent type recommended by the manufacturer. You can help preserve our environment by returning your unwanted batteries to your nearest point for collection, recycling or proper disposal. Note: In some areas the disposal of nickel cadmium batteries in household or business trash may be prohibited.
Call toll free number: United States and Canada only Caution: Do not handle damaged or leaking nickelcadmium batteries. Explosionsgefahr bei unsachgem?? Ersatz nur durch denselben oder einen vom Hersteller empfohlenen? Entsorgung gebrauchter Batterien nach Angaben des Herstellers. Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat bij einde levensduur afdankt.
Gooi de batterij niet weg. Lithiumbatteri-Eksplosionsfare ved fejlagtig h? Udskiftning m? Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA. Installation Overview Supplied Accessories Connection Connector System Setup Audio System Settings for the Intercom Systems Setting the Program Microphone Signal Setting for the Tally System Setting the Camera Numbers Resetting the Control Data Adjusting the Phases of the Signals Adjusting the Triax Signal Adjusting the Level of the Signals on a Waveform Monitor Adjusting the Level of the Signals on a Picture Monitor Adjusting the Y.
Adjusting the Signal of the Optional Boards When Adjustments are Finished Service Overview Board Layout Removal and Installation of Flexible Card Wire Spare Parts 5.
Block Diagram Overall Block This manual is intended for use by trained system and service engineers, and provides the installation and maintenance information that is necessary at the time of primary service. Maintenance Manual Part 2 Available on request This manual describes the information items on maintenance, and items that premise the service based on the components parts such as adjustments, parts list, semiconductor pin assignments, block diagrams, schematic diagrams and board layouts.
System Manual Available on request This manual is necessary for connection and operation of video camera and other peripheral equipment. Section 2 System Setup Describes setting and adjustment for connecting this unit to the camera system. Section 3 Service Overview Describes information about board locations, circuit description and function of internal switches. Section 4 Spare Parts Describes spare parts list such as plug-in board, fan and fuse used in this unit.
Section 5 Overall Block Diagram Describes overall block diagram. Supplied Accessories Accessories Remote indicator! Adaptive Connectors and Cables Rear panel [Input signals]. DM Connector Setting. For more details, please consult your Sony service representative. Operating Environment Outer Dimensions Connection Connector Use the connectors below or the equivalent at its tip when cables are connected to each connector on the connector panel during installation and servicing.
Do not put the unit in a place subject to high temperature or in a location near heat sources. Do not put the unit in a place subject to excessive electric and magnetic fields. Put the unit in a dry and well-ventilated place. Do not put the unit in a place subject to excessive dust and mechanical shock. Do not put the unit in a place subject to direct sunlight and light. Mounting on Inch Rack Mounting 1. Tighten the four rack mount screws.
In this case, since no power is supplied to the camera head side, use a camera head that conforms to the stand-alone specification. For the camera head side, convert the triax connector into a BNC connector. Instance of System Configuration Audio System Settings for the Intercom Systems This unit can use two intercom lines independently, a producer line and an engineer line.
Since this unit conforms to the 4W and RTS intercom systems, set the internal switch in accordance with the system to be used. Selecting the intercom system Select the intercom system, 4W or RTS, for each engineer or producer line. Also, select the number of intercom lines 1 channel or 2 channels. Factory setting: 4 W. When one-channel intercom line is used. When two-channel intercom line is used. Otherwise oscillation may occur. Audio System 2. Factory setting: 0 dB. When the switch is set to PRIV, the external intercom line is deactivated, and only the intercom with the camera is activated.
Switch settings on the AU board The switch settings and the signal flow of the AU board are as shown below. Refer to the below diagram. Select either step of the following. Setting the microphone input level control Pin No. Control System Setting for the Tally System This unit conforms to red-tally and green-tally systems and also to contact supply and 24 V power supply.
Set switches on the AT board according to the tally system to be used. Set the least significant decimal digit LSD with switches 1 through 4, and the most significant decimal digit MSD with switches 5 through 8 as shown below. Camera numbers set with these switches are from 1 through For more details, see system manual. Video System Before starting operation, check the levels of the units, and adjust them if necessary. For such items, perform basic adjustment with the switches and controls on the boards, and fine adjustment with the maintenance menu.
Resetting the Control Data Before adjustment, reset the control data of the unit. Set the S to ON. The control data are then reset. Adjusting the Phases of the Signals Adjust the signal phase of the unit. Before starting adjustment, input the following sync signals to the unit and all equipment connected.
Sony Ccu-550a Wide-band Camera Control Unit
Login Sony ccu m3 manual Sony dxca dxc service manual rev 2 complete. Sony camera control unit model ccu-m3 Hot new sony tvl 3. Sony original supplement-1 manual for dxc-c1 dxc-c1mdp color video camera. Sony camera control unit ccu-m3. Hot new nillkin sparkle leather case for sony xperia z3. Dark side of rainbow 5. Sony ccu camera control unit.
CCU 550A PDF
There are 3 items available. To adjust the SC phase 7. You will receive what is shown in the photo unless there is more than 1 available or otherwise stated. See all spartasale has no other items for sale. Please enter a valid ZIP Code. See other items More Max 30 mA 11 12 13 14 15 NC Removing the Top Cover During factory setting, this switch is set so that the H blanking width is For additional information, see the Global Shipping Program terms and conditions — opens in a new window or tab No additional import charges on delivery Delivery: To reduce the risk of electric shock, fire or injury, do not perform any ccu other than that contained in 55a operating instructions unless you are qualified to do so. Free shipping and returns.
Sony ccu m3 manual